Search results for "Shear test"
showing 10 items of 12 documents
The shear strength of Opalinus Clay shale in the remoulded state
2020
Abstract The Opalinus Clay shale formation is considered as a potential host geomaterial for the Swiss deep geological repository for radioactive waste. It presents different facies and it is characterised by a multi-scale heterogeneous composition, by a typical fissile structure with well-defined bedding planes and by anisotropic hydro-mechanical behaviour. This peculiar complexity makes it difficult to assign a unique set of geomechanical parameters to the material. This paper presents an experimental study aimed at characterising the lowest values of the shear strength parameters. In this sense, the shear behaviour was investigated on remoulded samples where the fabric and the diagenetic…
Bond strength evaluation of the veneering-core ceramics bonds.
2009
The purpose of this study was to determine whether the bond of veneering porcelain to a ceramic core in bilayered ceramics was similar to that of the metal ceramic control of well known behaviour. Six groups of nine specimens each were fabricated, whose dimensions were 15 mm long and 8 mm in diameter at the core, and 2 mm long and 8 mm in diameter for the veneer. The groups were GR. 1 (control group): CrNi alloy/d.SIGN (Ivoclar), GR. 2: IPS e.maxPress/IPS e.maxCeram (Ivoclar), GR. 3: IPS e.maxZirCad/ IPS e.maxZirPress (Ivoclar), GR. 4: IPS e.maxZirCad/IPS e.maxCeram (Ivoclar), GR. 5: Lava Frame (3M ESPE)/ Lava Ceram (3M ESPE) and GR. 6: Lava Frame (3M ESPE)/IPS e.maxCeram (Ivoclar). A shear…
Analysis of bond strength between a nylon reinforcement structure and dental resins
2021
Made available in DSpace on 2021-06-25T10:30:27Z (GMT). No. of bitstreams: 0 Previous issue date: 2021-05-01 Background: Nylon is a polymer that its use to reinforce dental resins has shown positive results such as increased flexural strength. The aim of this study was to evaluate the bond strength between dental resins and a nylon reinforcement. Material and Methods: Forty cylindrical nylon blocks with 13 x 23 mm with 0.5% by volume of silica and 40 without were made. Half of the samples of each nylon composition were sandblasted with aluminum oxide (50µm) for 3 s (2.8 bar pressure, distance: 20 mm, incidence angle: 90o). On the nylon blocks, cylinders of chemically activated acrylic resin…
A shear test for structural adhesives used in the consolidation of old timber
2001
A test method was developed specifically for structural adhesives used in thick joints. It is based on compressive shear loading of glued joints (GJ) and solid wood (SW) specimens, before and after a suitable accelerated ageing cycle. The evaluation of results is based on the ratios of wet strength to dry strength and on the comparison of GJ specimens to SW specimens which are prepared from the same batch of wood, in order to minimise the influence of the variability in wood characteristics. On a group of 10 epoxy-based adhesives, specifically marketed for the consolidation of old timber structures, the method has proved to be effective to differentiate the performances of each product. Amo…
Friction stir welding of lap joints: Influence of process parameters on the metallurgical and mechanical properties
2009
Abstract Aluminum alloys are widely used in the aircraft industries even if such materials present lower ductility with respect to steels, anisotropy phenomena and, more important, they are often “difficult” to be welded or even “non-weldable”. In the last years the friction stir welding process (FSW) was proposed and applied in order to get good mechanical and technological performances of the joints. In this paper, an experimental and numerical investigation on the lap joining of AA2198-T4 aluminum alloy blanks by FSW is presented. In particular the joints strength and metallurgical properties are investigated by varying the joint configuration and the tool geometry and rotational speed. …
Comparison between a Uniaxial Compaction Tester and a Shear Tester for the Characterization of Powder Flowability
2014
The complete characterization of powder flow properties with shear cells is a long and time-consuming process that requires specially trained operators or costly automated instruments. For these reasons, in industrial practice, the use of simpler and less extensive measurement by uniaxial compaction testers is often preferred. However, previous studies in the literature indicate that the results of the two techniques are not directly comparable due to the different stress state conditions achieved in the two testers.In this study, an experimental campaign to measure the flow function of five different powders with a ring shear tester (RST) and a uniaxial compaction tester (UCT) was performe…
On the hydro-mechanical behaviour of a lime-treated embankment during wetting and drying cycles
2018
Abstract The paper presents some experimental results obtained on samples extracted from a full-scale embankment obtained by compacting a lime-treated clayey soil. A comprehensive test programme was carried out in order to highlight the improvement of mechanical behaviour induced by lime treatment as well as to assess the durability of the improved material, which may be affected by severe seasonal wetting and drying cycles. Direct shear tests, triaxial compression tests, swelling potential measurement and oedometric tests were performed on samples cured in controlled environmental conditions for at least 18 months. Wetting and drying cycles were applied in a very wide range of suction valu…
Shear Strength of a Compacted Scaly Clay from Suction-Controlled Triaxial Tests
2012
The paper presents the results of an experimental research aimed at investigating the shear strength characteristics of an unsaturated compacted scaly clay. Shear strength was investigated by suction-controlled triaxial compression tests on dynamically compacted samples. Collected results point out that suction effects on stiffness and shear strength can be very different for suction values applied lower or greater than air entry value (AEV), corresponding to the material void ratio.
Influence of delay between dental bleaching with 35% hydrogen peroxide and orthodontic brackets on the bond strength at the enamel/adhesive interface
2019
Background The aim of this study was to evaluate the influence of waiting time between the bleaching with 35% hydrogen peroxide and orthodontic brackets bonding on shear bond strength (SBS) in enamel. Material and Methods Eighty bovine teeth were randomly divided into four groups (G): G1(negative control) and G2, G3 and G4 (experimental groups). The experimental groups were submitted to bleaching. Prior to orthodontic brackets bonding to enamel the procedure was adopted different waiting times, as follows: G2 (1 day); G3 (7 days) and G4 (14 days). It was performed enamel etching (30s), washing water (30s), application of adhesive system followed by photoactivation (20s). A thin layer of com…
Characterisation of Fibre Glass Panels for Naval Use
2004
This work examines the characteristic of fiber glass composite panels constructed by Cantieri Arturo Stabile in Trapani (Italy): composite materials are very used in the naval applications, where high stiffness and resistance are required with reduced weight. Experimental tests are executed following ASTM or UNI EN rules, in particular the shear test is executed using a rig constructed to the purpose, designed following the rule ASTM D 4255-83. Besides the tests were simulated by analytical methods, by means of Cadec software and numerically by FEM software as Altair Hyperworks and Ansys, to evidence the error range of the experimental test and to obtain the configuration that can give suit…